Vacuum Hot Air Drying Equipment

  • Vacuum Hot Air Drying Equipment Manufacturers, Vacuum Hot Air Drying Equipment Factory, Supply Vacuum Hot Air Drying Equipment
  • Vacuum Hot Air Drying Equipment Manufacturers, Vacuum Hot Air Drying Equipment Factory, Supply Vacuum Hot Air Drying Equipment
Vacuum Hot Air Drying Equipment
  • LG VACUUM
  • JIANGSU CHINA
  • 30 DAYS
  • 100 SETS/ YEAR

The top of the Vacuum Hot Air Drying Equipment set a big air volume, low noise and heat-resistant type centrifugal fan.

Product Overview:

Vacuum Hot Air Drying Equipment is a special drying equipment for transformer in the whole process of hot air circulation and automatic intelligent control.

The top of the curing stove set a big air volume, low noise and heat-resistant type centrifugal fan. Heating chamber is set inside the air duct on both sides of the tank.When  working,the working chamber adopts the way of wind in the lower part of the left and right air duct (about 1/3 height), vertical air supply,each part is heated at the same time outside the work;

After the hot air and workpiece in the working room are fully exchanged, the air flow can be returned to the top suction chamber evenly, and then the fan is sent into the wind tunnel (heating chamber) to be heated again and again.

Due to the high wind volume, the high wind pressure circulating fan carries out the forced hot air circulation, which ensures the good temperature uniformity in the work room.

The temperature of the solidified furnace can meet the technological requirements.


Technical Paramemter of Vacuum Hot Air Drying Equipment:

Open the door way

 Double manual door on front of curing furnace

The gate structure

The door lock adopts the adjustable structure of the horn handle, the material adopts the cast steel chrome-plated door handle;

Door hinge up and down a set, a total of two sets, chrome-plated surface treatment;

Protective cushion, a nylon protective cushion is provided above and below each door to prevent the door from being impacted too much

Door panel: Q235 cold-rolled steel plate is welded after rust removal and rust prevention treatment;

Door bottom and frame plate: Q235 cold-rolled steel plate is welded after rust removal and rust prevention treatment;

Door frame: Q235 channel steel, Angle steel and other steel derusting and rust prevention after derusting and rust prevention treatment and welding;

Door insulation: high density aluminum silicate cotton insulation and mineral wool insulation board filling;

Door seal: asbestos rope:

Technical reference number

Electrical source

3N+PE  380V  50Hz

Using temperature range

At room temperature to 200 ℃ (adjusted)

Temperature fluctuation

≤±1℃

Temperature uniformity

≤±2.5%(refer to empty box test with maximum service temperature)

Heating power

60kW

Air-blast system

Y802-4Long shaft motor: special temperature resistant long shaft blower motor y802-4 

The blades: Ф centrifugal 

Wind leaf volume: 255 x 100 mm 2600 m3 / h 

wind pressure: 370 pa

Exhaust system

Long shaft motor: special temperature resistant long shaft blower motor y802-4

Blades: Ф centrifugal wind leaf volume: 200 x 80 mm 2000 m3 / h

Blast system

Hot air circulation

Forced hot air circulation from both sides of the lower part of the studio, vertical upward, and even air return from the top

Hot air outlet

200mmThe upper part of the trolley is equipped with 200mm air outlet

Air return method

 

Multi-hole equalizer return air at the top of the studio

Blowing machine

Multiple centrifugal blowers with large air volume and low noise are adopted, and the noise is below 65dB

Blower position

It is arranged in the air duct at the top of the housing

Add hot system

The electric heater

Star connection 220V 50Hz U surface low load electric heat pipe

Heater position

The heating chamber is arranged in the air ducts on both sides of the studio

The furnace body temperature

Insulation thickness


The furnace body is 100 ~ 120mm thick, and the door is 130mm thick

Insulation layout


The heater is placed on aluminum silicate cotton felt, and the rest is insulated with aluminum silicate cotton

The surface temperature of the box rises


Furnace body surface temperature at room temperature or less + 15 ℃ (J standard for room temperature + 35 ℃), special position reference to standard JB/T5520-91

Pallet size


Manual trolley 1 set 1800 3800(width depth)

Type of drive

Manual traction

Car frame

It is made of Q235 steel and sprayed with W61 series silicone heat-resistant paint after rust removal and rust prevention

Car panel

It is made of Q235 thick steel plate with honeycomb air holes and sprayed with W61 series silicone heat resistant paint after rust removal and rust prevention

Vehicle wheel

The car with Ф 200 a total of 4 sets of wheel load system

Pallet load

Load ≤ 5 tons


Electric control system

Temperature control system

 

The curing furnace is equipped with a set of xiamen yudian AI518P intelligent digital display temperature controller, which can be programmed with 30-segment rise program, with P.I.D parameter self-setting, with RS485 computer communication interface, and with temperature sensing element Pt100

Alarm system

 

Each curing furnace is equipped with a set of yuguang AI508 digital temperature controller with RS485 computer communication interface and Pt100 temperature sensor

Heating control

 

Adopt solid state relay contactless power regulation, adopt photoelectric isolated input level, TTL level compatible input, automatic power regulation, zero crossing trigger, dc or pulse trigger mode, with contactless, no mechanical moving parts, no spark, no action noise, vibration resistance, long life and so on

Blast control

Set up a drum risk control system

Exhaust control

  Timing clearance type automatic exhaust, manual/automatic conversion

Protection system configuration

1. Two sets of over temperature alarm systems are set for each unit. When the temperature inside the box is abnormal, an audible and visual alarm will be issued and the heating power will be cut off automatically;

2. Motor over-current protection prevents motor from burning down and tripping;
3. Over current protection of electric heater prevents short circuit of electric heater;
4. The motor and the heating interlock device must be heated after blowing to prevent the electric heater from burning out;
5, control line protection to prevent circuit short circuit, causing accidents;
6, the air switch to prevent the main circuit overload and short circuit, causing accidents

Description of the cementing furnace accessory

Inlet valve

Equipped with multi-blade manual air inlet valve, manually adjust the air intake according to the need

Sling

Hanging rings are set at the bottom bracket for easy lifting

External guide

Suitable for pouring tanks


External exhaust pipe

The supplier reserves flange interfaces, and the demander is responsible for installing and making external exhaust pipes according to the needs

Color

Box light gray, the door orange red or by the user


Details Show:

Hot Air Drying Equipment


Hot Air Drying Equipment


Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy

close left right